Outlaw RC Product Listing

Outlaw RC billet beadlocks are machined out of solid aluminum. These are outer bead locks only and we reccommend using Silverback inner beadlocks.
These beadlocks do more than just look good! They replace the stock plastic beadlock rings and increases the strength and rigidity of your stock rim. No longer will you suffer from bolts pulling through the beadlock. We reccomemend using the Nylock wheelscrew kit to ensure the beadlock cannot separate from the rim even under severe bashing conditions.
These come as a complete set of 4 outer beadlocks in the following colours: Silver, Black, Blue, Purple and Red.
Pairs and singles also available.

Click on the images to enlarge.

Outlaw RC heavy duty front upper chassis brace for Baja 5b. Tuff Australian made product will greatly increase the front end strength and looks good aswell.
Machined out of solid Australian made aluminium plate and includes stainless steel bolts.

Click on the images to enlarge.

Fully enclosed wheel nuts provide a large flange surface and also reduces the ingress of dirt, water and mud into the hub area.
Set of four(4) wheel nuts. Machined from billet aluminum.

Click on the images to enlarge.

Outlaw RC rear alloy engine mount to replace the stock plastic part. Extra strong as it attaches to the fan cover in two places instead of one like the stock part.
Note: These are designed to suit CY and Zenoah fan covers. Other brands may not have the same hole spacing requiring some modification of the mount to fit.

Click on the images to enlarge.

Outlaw RC heavy duty front lower chassis brace for Baja 5b. Tuff Australian made product will greatly increase the front end strength.
Machined out of solid Australian made aluminium plate and includes stainless steel bolts.

Click on the images to enlarge.

Outlaw RC heavy duty 8mm rear upper turnbuckles. These turnbuckles are the biggest and strongest available for the HPI Baja. Zinc plated so they will not rust. They have a left and right hand screw thread and a hex in the centre so they can be adjusted by simply turning them one way or the other using a suitable wrench.
Installation will require enlarging the existing thread holes in stock or RPM plastic upper arms with a 6.8mm drill.
These will NOT suit alloy rear upper arms unless they are moddified with an 8mm thread.

Click on the images to enlarge.

Alloy roll cage risers. Commonly used with rear dominator pipes to lift the roll cage away from the pipe so it does not melt. Includes R-clips for the upper hole.

Click on the images to enlarge.

Standard Size Servo Adaptor - Standard size servo adaptor. This adaptor bolts in place of the stock large scale steering servo on a Baja and allows a standard size servo to be fitted.

Alloy Servo Mount Adaptor - Alloy servo mount adaptor, used when fitting aftermarket servos such as Hitec 5745, 5755 and Multiplex Rhino.

Click on the images to enlarge.

Outlaw RC foam air filter. This filter is designed to be oiled completely to ensure adequate filtration. The foam used is an extra fine medium on the outer layer and a low restriction medium on the inner. This filter is designed to provide the best filtration in dusty conditions. Requires a velocity stack for use and easy to get on and off using the supplied clamp. Filter separates into two pieces for thorough cleaning. Outerwears Prefilter for HPI Baja reccommended to give maximum use before cleaning is required. Fits all 2 stroke spark ignition engines use in 1/5th scale vehicles.

Outlaw RC high flow foam air filter. This filter is designed to be oiled completely to ensure adequate filtration. The foam used is a low restriction medium ideal when chasing maximum performance. Requires a velocity stack for use and easy to get on and off using the supplied clamp. Filter separates into two pieces for thorough cleaning. Outerwears Prefilter for HPI Baja reccommended to give maximum use before cleaning is required. Fits all 2 stroke spark ignition engines use in 1/5th scale vehicles.

Click on the images to enlarge.

HPI Baja Full Bearing Kit - This kit will replace all the bearings on the Baja as well as replace the bushes in the diff with bearings. High quality ABEC 5 rated rubber shielded bearings. Available with and without Flanged Bearings. Kit consists of:
2 of 20 X 32 X 7
4 of 10 x 15 x 4
4 of 5 x 10 x 4
2 of 17 X 30 X 7
13 of 12 X 24 X 6

HPI Baja Wheel Bearing Kit - This kit will replace all the wheel bearings on the Baja. High quality ABEC 5 rated rubber shielded bearings. Kit consists of:
8 of 12 X 24 X 6

HPI Baja Diff Bearing Kit - This kit will replace all the diff bearings on the Baja and replaces the bushes with bearings also. High quality ABEC 5 rated rubber shielded bearings. Kit consists of:
4 of 10 X 15 X 4

Click on the images to enlarge.

HPI Baja Gearbox Bearing Kit - This kit will replace all the gearbox bearings on the Baja. High quality ABEC 5 rated rubber shielded bearings. Kit consists of:
2 of 17 X 30 X 7
2 of 12 X 24 X 6

HPI Baja Clutch Bearing Kit - This kit will replace all the clutchbell and pinion bearings on the Baja. High quality ABEC 5 rated rubber shielded bearings. Kit consists of:
2 of 12 X 24 X 6

HPI Baja Steering Bellcrank Bearing Kit - This kit will replace all the bellcrank bearings on the Baja. High quality ABEC 5 rated rubber shielded bearings. Kit consists of:
4 of 5 X 10 X 4

Click on the images to enlarge.

Heavy Duty Front and Rear Springs for the HPI Baja. These are stiffer components than the stock items.

Click on the images to enlarge.

Outlaw RC Direct servo power harness designed specifically for your Baja 5B/5T. Also suitable for other Large Scale RC cars running 2 servos.
Connects between power switch, reciever and servos to provide a direct feed of power to the servos. By passing the reciever allows the servos to pull a greater current and operate to there full potential of speed and torque.
Eliminates the failsafe cutting in due to high servo current draw.
Avoids damaging your reciever due to high current draw from modern digital servos.
Suits all transmitters/receivers AM/FM or 2.4Gig

Servo Y lead. For running two servos off the one channel, most commonly dual steering servos. 150mm long, 22awg wire suitable for high current draw digital large scale servos.

Receiver Switch.

Click on the images to enlarge.

Screw kit for HPI Baja RTR and SS. Contains over 400 screws, nuts and washers. This kit will replace all the metric thread socket head, flat head and button head screws as well as locknuts,washers, imperial wheel screws and set screws. Screws are all grade 12.9 high tensile.
Standard screw kit includes standard length 4-40 wheel screws, a separate kit is available with longer 4-40 wheels screws and nylock nuts for improved outer beadlock holding ability.
Kit comes packed in a convenient plastic storage box with a lid that snaps firmly shut. Finding the screw you need is very easy and the 21x13x3cm box takes up minimal space in your pitbox.

Nylon Wheel Screw Kit is NEW AND IMPROVED! We have changed from metric screws to imperial screws as they fit the beadlocks better.
Nylock wheel screw kit. This kit contains 4-40 x 5/8" screws and nylock nuts to securely hold the outer beadlocks to your rims.
The standard wheelscrews are prone to pulling out of the rim. These screws extend right thru the rim so a nut can be fitted to inside of the rim eliminating any chance of the screws pulling out of the rim.
Each kit contains 22 screws and nuts, enough to do two(2) rims and a couple of spares.
They are fitted to the outer beadlock only.
Installation only requires the screws and nuts to be nipped up finger tight. Overtightening is not neccessary and may pull the screwhead through the beadlock.

Click on the images to enlarge.

Multiple outlet charging adapter. This unit has the common male banana plugs on one end and then its nicely split into 4 different types of common battery plugs on the other end as well as a bare set of wires for another type of plug of your choice. Take the mess out of your charging with this charger adaptor.

Charger lead with Tamiya plug. 4mm banana plugs will fit most common chargers.

Click on the images to enlarge.

30ml Bottle of high quality air filter oil. Convenient eye dropper nozzle.

Outlaw RC 'TUFF-LINE' fuel line is a flexible transparent tubing specially formulated for fuels and oils. More flexible and will not harded over time like common polyurethane tubes. 1/8" ID x 1/4" OD.

Replacement Pullstarter rope for all 1/5 pullstarters. High quality 16 Platt rope in 1 metre lengths. Keep a length in your toolbox it could save you missing a days bashing!

Click on the images to enlarge.

MSD high quality spark plug wire, terminal and boot. Made to be a direct replacement to your stock plug wire found on all Zenoah and CY engines. Comes complete with glue lined heat shrink and instructions. Requires installer to remove fan cover for proper installation. When used with stock plastic spark plug cover on the Baja 5b, it does make for a tight fit but it does fit. Also suits engines fitted to MCD's, FG, Carson, Smartech and most other large scale cars.

Choose from Black, Red, Blue, Green, Purple, Yellow, Orange.

Click on the images to enlarge.